Genesys 2 - Programming Guide

There are four ways you can program the Genesys2:

• JTAG
• Quad SPI Flash
• USB Flash Drive
• Micro SD Card

This tutorial will walk you through what you need to know to get started on your projects and program your Genesys2 FPGA board using each of the three possible methods. It is recommended that you first complete the “Getting Started with Vivado” guide before continuing with this project.NOTE: The Genesys2 requires Vivado Design Edition or System Edition which supports the Kintex-7 FPGA. This is not the same as the free webpack version.

• Basic familiarity with Vivado
  • This experience can be found by walking through our “Getting Started with Vivado” guide

• Genesys2 FPGA board
• Micro-USB cable
• Micro SD card

• Vivado Design Suite 2015.X
  • System Edition or Design Edition must be installed to support Kintex-7

• Genesys2 Support Files
  • These files will describeGPIOinterfaces on your board and make it easier to select your FPGA board and addGPIOIP blocks.
  • Follow the Wiki guide:Vivado Board Files for Digilent 7-Series FPGA Boardson how to install Board Support Files for Vivado.

Source Files–ZIP

First we will need to create a project.

1.1) Open up Vivado and clickCreate New Projectto open Vivado's New Project wizard.

1.2) A new window will open up, clickNextand you'll see the screen below. Name your project (no spaces!) and choose your project saving directory before clickingNext.

1.3) We will be building this project from the ground up and adding our own sources so we will want to create an RTL project. select RTL Project and clickNext.

1.4) In this window, you can select any source files or directories that you'll want to use in your projects. We can also select which language we'll be programming in. For this project just keep the default settings. Create a new file by clicking theCreate Filebutton.

1.5) Findsw_led.vwithin the source files folder you downloaded and clickOk. TheCopy sources into projectcheckbox will be enabled by default. This creates anothersw_led.vwithin our project directory so that the original will not be altered. ClickNextto continue.

1.6) This window lets you choose existing IP (Intellectual Property) cores if you have them, but for this tutorial no IP's will be necessary. ClickNext.

1.7) This is where we'll import our Xilinx Design Constraints file (XDC) to map the HDL signals to the Kintix-7 pins. ClickAdd Files, navigate to where you saved your Genesys2_H.xdc file, select it, and clickNext.

1.8) At this point Vivado will open up a part selection window. Select theBoardstab highlighted in orange below. If you installed the board files correctly, you should see a list of Digilent boards. Select theGenesys2and clickNext.

This will create your project and bring you to the Vivado project manager.

You have now successfully created/imported your program files and configured your project to properly communicate with the Genesys2.

For the four ways to program your Genesys2 FPGA there are two file types available; .bit and .bin files. Using a .bit file we can use either the JTAG programming cable, or a standard USB storage device to load the bit file into the FPGA. Programming with a .bin file will use the QuadSPI to program the FPGA each time it is powered on. This means you will not have to reprogram it each time via a micro USB cable or by a thumb drive. The following steps bellow will get you all prepared to program your Genesys2.

2.1) In order to program the FPGA on startup we have to specify that we want to generate a .bin file. This can be done by clickingTools→Project Settings→Bitstream. In this window we will check the box next to .bin_file. Now Vivado will create both a .bit, and .bin file when we generate a Bitstream.

2.2) To begin, we will run the synthesis by clickingRun Synthesisbeneath Synthesis in the Flow Navigator on the left side of Vivado.

2.3) When the program finishes synthesizing your project, you will see the Synthesis Completed window below. ClickOpen Synthesized Designand then pressOk.

2.4) You should now see your Synthesized Design in the window to the right. It should look like this:

2.5) To improve programming speed of our .bin file, in the main toolbar selectTools→Edit Device Properties. Under General, setEnable Bitsream Compressionto “TRUE”.

2.6) Under Configuration, setConfiguration Rate (Mhz)to33.

2.7) Under Configuration Modes, selectMaster SPI x4.

2.8) ClickOk, save your synthesized design (Ctrl+S) and then clickGenerate Bitstreamin the Flow Navigator on the left side.

2.9) This will open a box stating that you have not implemented your design. ClickOk.

2.10) Vivado will begin generating your bit and bin files. When completed Vivado will show you this box. Feel free to selectOpen Implemented Design, orView Reportsbut you can also justCancelto continue with the guide.

At this point you have successfully created a .bit and .bin file that are ready to program the Genesys2. As said previously there are four ways to program the Genesys2 FPGA board, and we will be walking through each one of them below.

JTAG is primarily used as a programming, debugging, and probing port and communicates through the micro-USB port. This makes interfacing with the Genesys2 easy because the micro-USB connection both supplies power to your board, and the ability to program it.

3.1) First, make sure that the jumper JP5 is in the JTAG position and that the Genesys2 is plugged into your computer via micro-USB cord into theJTAGport. Once the board is plugged in you should see something like this.

3.2) ClickProgram device(in the green bar), then clickxc7k325t_0, and select your .bit file in thebitstream filebox, and clickProgram.

This will program your Genesys2 through the JTAG connector. Once the programming window is closed go ahead and test out your board. Each slide switch at the bottom of your board should now toggle its respectiveLEDon and off.

重要的是要注意,y的USB设备ou select to program the Genesys2 must be formatted in Fat32. Other than that your device doesn't have to be empty and can contain other files and folders. At this point Vivado is no longer needed to program the FPGA, so you can minimize your project and follow these steps in File Explorer:

4.1) Make sure the jumper on JP5 is in the USB/SD position and that JP4 is in the USB position if using a USB drive, or SD if using an SD Card.

4.2) Plug your USB flash device or SD Card into your computer.

4.3) Open File Explorer and navigate to the root folder of your Vivado project.

4.4) From root go toroot→Project_name.runs→impl_1and copy the .bit file.

4.5)去你的USB设备粘贴t的根源he .bit file. The Genesys2 on startup will only look through the USB's root for a file with a .bit extension so it is important that the only .bit file in root is the one that you want to be used to program the Genesys2.

4.6) Safely remove the device from your computer and plug it into the Genesys2.

4.7) Make sure your board is connected to your computer for power and turn on the Genesys2. It should immediately begin writing the .bit file to the FPGA.

Once finished your board should function exactly as it did when programming it with JTAG. Whether you were aware or not you just successfully programmed your Nexsys 3 board two separate ways using the same .bit file.

Quad SPI Flash is a non-volatile memory that the Genesys2's FPGA chip looks at on every startup. If Quad SPI is flashed then the FPGA will program itself with the contents found in Quad SPI's flash memory. This method of programming your board is great when you have a final project that you would like to demo or display that doesn't need to be edited and therefore reprogrammed.

5.1) Make sure the jumper on JP5 is in the QSPI position

5.2) In the Hardware Manager window, under hardware right click your device and clickAdd Configuration Memory Device…

5.3) This window will pop up. Search for “Spansion” and selects25fl256sxxxxxx0-spi-x1_x2_x4. ClickOKon the next window asking if you want to program the configuration memory device.

5.4) Select the .bin file (found in your project/project.runs/impl_1/ folder) where it asks for a configuration file and finally clickOK.

Vivado will now erase the old configuration file, and reprogram your Genesys2 with the demo file. From now on, when you power up the Genesys2, the demo will load at startup until you reprogram it.